## How to Fix Electrolux Error E35 (Water Overflow)
When your Electrolux washing machine displays the E35 error code, it’s indicating a critical fault related to water level management. This guide will help you understand the issue and provide a structured troubleshooting process.
—
### 1. Explanation: What Electrolux Error E35 Means
**In plain English, Error E35 means your washing machine has detected a potential or actual water overflow condition.**
The machine believes that the water level has risen above the maximum safe limit, which is typically sensed by the pressure switch. This is a critical safety feature designed to prevent flooding your laundry area.
**Likely Causes:**
* **Faulty Pressure Switch (Most Common Culprit):** The sensor responsible for measuring the water level is stuck in the “full” or “overflow” position, even if the tub is empty or correctly filled.
* **Clogged Pressure Chamber/Hose:** Debris or detergent residue is blocking the air trap or the small hose connecting the tub to the pressure switch, preventing an accurate reading.
* **Control Board Malfunction:** Less common, but the main electronic board (PCB) may be misinterpreting the signal from the pressure switch.
—
### 2. Step-by-Step Fix: Diagnosing and Repairing E35
**⚠️ Safety First:** Always unplug the washing machine from the power outlet before inspecting or handling internal components. Turn off the water supply taps.
#### Step 1: Drain and Reset the Machine
Before attempting a physical repair, ensure the error is not a transient glitch:
1. **Unplug the machine** for at least 5 minutes.
2. **Manually drain the machine:** Locate the drain pump filter, usually behind a small panel at the bottom front of the machine. Place a shallow tray underneath and slowly twist the cap to drain all remaining water.
3. **Check the Sump Pump:** Clean out any debris (coins, hair, lint) found in the drain pump filter cavity.
4. **Plug the machine back in** and attempt a short cycle (e.g., rinse/spin). If the error immediately returns, proceed to Step 2.
#### Step 2: Inspect the Pressure System (The Hose and Chamber)
The pressure switch works by measuring the air pressure exerted by the water level rising in the drum. If the passage is blocked, the switch cannot read the level correctly.
1. **Locate the Pressure Switch:** This is usually a small, round component with a thin rubber or plastic hose attached to it. It is often located near the top of the machine, behind the control panel or near the main drum housing.
2. **Trace the Hose:** Follow the thin pressure hose from the switch down to where it connects to the tub (the air trap or pressure chamber).
3. **Remove and Inspect:** Carefully detach the hose from both the switch and the tub connection.
4. **Check for Clogs:** Blow through the hose to ensure it is clear. If resistance is felt, use warm water and mild detergent to flush out any gunk or debris.
5. **Check the Air Trap/Chamber:** Ensure the port on the tub where the hose connects is also free of soap scum or blockages.
#### Step 3: Test or Replace the Pressure Switch
If the hose and air trap are clear, the sensor itself is the most probable cause of the E35 error.
1. **Test Continuity (Optional, Requires Multimeter):** If you have a multimeter, you can check the resistance or voltage of the switch according to your machine’s service manual. However, since the E35 error indicates a continuous “overflow” signal, the switch is likely stuck closed.
2. **Inspect Wiring:** Check the electrical connector harness leading to the switch. Ensure all wires are firmly seated and that there are no signs of corrosion or heat damage.
3. **Replacement:** If the hose is clean and the wiring is sound, replacing the Pressure Switch is the most reliable way to solve the E35 error. This component is designed to be user-replaceable.
—
### 3. Call to Action
Check the price for a replacement Pressure Switch here: https://www.amazon.com/s?k=Electrolux+Pressure Switch&tag=trivian-20